vacuum pump

The Oil Sludge from the Crude Oil Tank, Refinery Plant, or Drilling Waste is always a big headache for the operators, while it is economy to recycle the oil contained, and the solid shall be discharged suitable for environment.

The treatment for oil sludge cannot be achieved with just one or two equipment, it shall be a system.

Today we shall introduce a Reliable and Economy Oil Sludge System from GN Solids Company.

Oil sludge is a mixture consisted of oil water and solids.

To treat the waste oil sludge and recovery oil and water, the oil, water and solids must be separated. And also it is important to dispose of the solids inexpensively and recover oil as much as possible. GN decanter centrifuge and oil water separator and thermal desorption unit is to do the job.

 

Brief Introduction about Working Procedure,

Firstly, the Oil Sludge pumped into the Pre-Mixing Tank for heating and mixing with chemical material.

Secondly, the sludge feed into the shale shaker for removing the big solid.

Thirdly, the sludge feed into the decanter centrifuge for removing the find solid.

Fourthly, the sludge feed into 3 Phase Separation Module, including Inclined Plate Separator, Oil Water Separator.

Fifthly, the collect the clean water and oil separately, and the Solid would be discharged separately too.

The recycled water can be reused in the washing process, and the oil is clean enough to sell to the refinery company, the solids contain oil between 2%-5% which can be sent to biodegradation or thermal unit for final disposal.

(Attn, different areas and different clients has different oil sludge and final requirements for the oil sludge treatment, following questions are needed to be clear for GN to provide the best proposal for your oil sludge treatment solutions.)

Welcome to contact us for more information!

GN SOLIDS COMPANY (11 YEARS FOR OIL SLUDGE TREATMENT)

After participation in the CIPPE 2018 in Beijing, China from 27th to 29th March, 2018, GN solids control will participate in OTC 2018 in Houston , TX. For more information of CIPPE 2018, pls check : http://www.gnsolidscontrol.com/drilling-fluids/welcome-to-gn-booth-for-the-2018-cippe-beijing-oil-show


We welcome you to visit GN at CIPPE 2018 in Beijing and visit GN factory where is 30km from the exhibition center during the oil exhibition.
OTC 2018 general information: for more information, pls visit their website: http://2018.otcnet.org/
Show Time & Location: 30 April – 3 May, 2018. NRG Park, Houston, Texas, USA
Booth No. 1: NRG Center 1369-1 (GN China)
Booth No. 2: NRG Arena 8000 (GN America)
What equipments will GN show at OTC?


Decanter centrifuge GNLW363C, this is the best sold model decanter centrifuge among all the decanter centrifuge models.
Shale shaker: GNZS594F-HB, we have many sets of shale shaker and mud cleaner in stock in Houston warehouse for immediate shipment, we install Martin brand vibration motor made in USA and assembly in our warehouse.
Sludge Vacuum pump:GNSP-20A, this is our new products in 2018, we have sold GNSP-40A vacuum pump for drilling cuttings transfer and dredging slurry transfer for dredging slurry separation system, sometimes the vacuum pump may not be suitable to transfer the oil sludge based on the sludge density and viscosity and the depth. GNSP-10A & GNSP-20A vacuum pump is the new designed model to meet the client’s requirement for smaller treating capacity.


Mud cleaner: GNZS594E-2S12N
Centrifugal pump, the installation dimension, outer dimension and spare parts are all interchangeable with Mission Magnum centrifugal pump.

GN solids control wish you and your families happy 2018 Chinese New Year, our holiday starts from Feb. 12th, 2018 to Feb. 25th, 2018, we will back to work on Feb. 26th, welcome to send us your inquiries during the holiday, our sales engineer will response at the earliest convenience. We appreciate your support during the past years, and we wish a longer term cooperation in the year of 2018.
The workers will stop working during the holiday and enjoy their time with families, but our sales will still hard working during the holiday to provide you immediate response.
During the past years, the best sold products are as below:


1) Shaker screens: The composite material frame shaker screens are very popular among international drilling companies in the world in the past years, we almost sold all the stocks and even can not meet the requirement of our clients. Especially for the OEM shaker screens for GNZS703, GNZS594E shale shaker, replacement shaker screens for Swaco Mongoose PT, Brandt King Cobra shaker, Venom, VSM 300 scalping shaker screens and primary shaker screens, FSI, MD-3, etc. screens.
2) Linear motion shale shaker and high G drying shaker: GN brand shale shaker has been widely used for oil & gas drilling solids control system, HDD & CBM mud recycling system, water based drilling waste management system.


3) Decanter centrifuge: GN 14inch bowl , 18 inch bowl, 22 inch bowl decanter centrifuge has been used for oil sludge treatment system, drilling waste management system, dewatering unit, solids control system, etc.

If you are looking for a good manufacturer of decanter centrifuge, vertical cuttings dryer, shale shaker, shaker screens, welcome to visit GN solids control stand at CIPPE 2018 to check our equipments.
Our stand info is as below:


We will show our best sold model decanter centrifuge at the show. As the largest and most professional oilfield industry products and service exhibition in China, all of the manufacturers will show their most advanced technology during the show.


GNLW363CG-VFD decanter centrifuge is one of the best sold model for our international clients, it can be used for solids control system, drilling waste management system, industry waste water treatment, dredging slurry separation, dewatering system, barite recovery, Low gravity solids separation, etc.
GNLW553C-VFD decanter centrifuge is the best sold big bowl big volume centrifuge, it is normally used as dewatering centrifuge with chemical dosing system for waste water treatment, it can be used for all kinds of waste water treatment. Sometimes it is used for oil sludge treatment system when the clients need 20~25m3/h treating capacity.


We will also show vertical G dryer GNCD930, it works together with GNLW363CG-VFD decanter centrifuge as drilling cuttings treatment system for oil based mud.
4 panel shale shaker GNZS594E installed with composite material shaker screens, with longer service life and better performance. We produce shaker screens in our own workshop, so GN solids control can control the quality by our own quality control dept. without purchasing from other suppliers. We produce OEM shaker screens for own shaker and replacement shaker screens for US brand shale shaker, like Derrick, Swaco, Brandt, FSI, Kemtron, etc.

If you are looking for a good manufacturer of decanter centrifuge, vertical cuttings dryer, shale shaker, shaker screens, welcome to visit GN solids control stand at CIPPE 2018 to check our equipments.
Our stand info is as below:


We will show our best sold model decanter centrifuge at the show. As the largest and most professional oilfield industry products and service exhibition in China, all of the manufacturers will show their most advanced technology during the show.
GNLW363CG-VFD decanter centrifuge is one of the best sold model for our international clients, it can be used for solids control system, drilling waste management system, industry waste water treatment, dredging slurry separation, dewatering system, barite recovery, Low gravity solids separation, etc.


GNLW553C-VFD decanter centrifuge is the best sold big bowl big volume centrifuge, it is normally used as dewatering centrifuge with chemical dosing system for waste water treatment, it can be used for all kinds of waste water treatment. Sometimes it is used for oil sludge treatment system when the clients need 20~25m3/h treating capacity.


We will also show vertical G dryer GNCD930, it works together with GNLW363CG-VFD decanter centrifuge as drilling cuttings treatment system for oil based mud.
4 panel shale shaker GNZS594E installed with composite material shaker screens, with longer service life and better performance. We produce shaker screens in our own workshop, so GN solids control can control the quality by our own quality control dept. without purchasing from other suppliers. We produce OEM shaker screens for own shaker and replacement shaker screens for US brand shale shaker, like Derrick, Swaco, Brandt, FSI, Kemtron, etc.