GN Solids Control will Exhibit at 2018 OTC in Houston USA

After participation in the CIPPE 2018 in Beijing, China from 27th to 29th March, 2018, GN solids control will participate in OTC 2018 in Houston , TX. For more information of CIPPE 2018, pls check : http://www.gnsolidscontrol.com/drilling-fluids/welcome-to-gn-booth-for-the-2018-cippe-beijing-oil-show


We welcome you to visit GN at CIPPE 2018 in Beijing and visit GN factory where is 30km from the exhibition center during the oil exhibition.
OTC 2018 general information: for more information, pls visit their website: http://2018.otcnet.org/
Show Time & Location: 30 April – 3 May, 2018. NRG Park, Houston, Texas, USA
Booth No. 1: NRG Center 1369-1 (GN China)
Booth No. 2: NRG Arena 8000 (GN America)
What equipments will GN show at OTC?


Decanter centrifuge GNLW363C, this is the best sold model decanter centrifuge among all the decanter centrifuge models.
Shale shaker: GNZS594F-HB, we have many sets of shale shaker and mud cleaner in stock in Houston warehouse for immediate shipment, we install Martin brand vibration motor made in USA and assembly in our warehouse.
Sludge Vacuum pump:GNSP-20A, this is our new products in 2018, we have sold GNSP-40A vacuum pump for drilling cuttings transfer and dredging slurry transfer for dredging slurry separation system, sometimes the vacuum pump may not be suitable to transfer the oil sludge based on the sludge density and viscosity and the depth. GNSP-10A & GNSP-20A vacuum pump is the new designed model to meet the client’s requirement for smaller treating capacity.


Mud cleaner: GNZS594E-2S12N
Centrifugal pump, the installation dimension, outer dimension and spare parts are all interchangeable with Mission Magnum centrifugal pump.

Continue reading “GN Solids Control will Exhibit at 2018 OTC in Houston USA”

400BBL Mud Tank System for Australia Drilling Company

This week GN Solids Control shipped 400bbl mud tank system to Australia drilling company. The configuration of the 400bbl mud tank system is as below:

1) 2 mud tanks, dimension: 12000x2800x1500mm, each tank with 200bbl tank volume, the stairs are outside of the mud tank to promise the largest tank volume.
Mud agitators are installed on top of the mud tank to prevent solids sedimentation.

2) 2 units of GNZS703F-HB linear motion shale shaker, installed with GN OEM composite material frame shaker screens, which is durable longer working life and larger effective screens area for better separation performance, the screens are with GN unique design locking system and the composite material frame make it stocked for over 5 years without getting rusted.
Normally we will package the shaker screens and wedges separately and bond on the shale shaker to avoid it get rusted during sea transportation.

3) Single skid amounted jet mud mixer and connect with the 2 mud tanks, it can mix the drilling fluids from any compartment of the 2 mud tanks except for the sand trap. Oilfield skid mounted design to promise the largest tank volume and easy maintenance. Separate control panel are installed on the skid to control the mixing pump.
4) All of the above equipments are IEC ex and the electrical cable, control panel, glands, etc comply with Australia explosion proof standard.

Continue reading “400BBL Mud Tank System for Australia Drilling Company”

Meet Good manufacturer of decanter centrifuge at CIPPE 2018

If you are looking for a good manufacturer of decanter centrifuge, vertical cuttings dryer, shale shaker, shaker screens, welcome to visit GN solids control stand at CIPPE 2018 to check our equipments.
Our stand info is as below:


We will show our best sold model decanter centrifuge at the show. As the largest and most professional oilfield industry products and service exhibition in China, all of the manufacturers will show their most advanced technology during the show.


GNLW363CG-VFD decanter centrifuge is one of the best sold model for our international clients, it can be used for solids control system, drilling waste management system, industry waste water treatment, dredging slurry separation, dewatering system, barite recovery, Low gravity solids separation, etc.
GNLW553C-VFD decanter centrifuge is the best sold big bowl big volume centrifuge, it is normally used as dewatering centrifuge with chemical dosing system for waste water treatment, it can be used for all kinds of waste water treatment. Sometimes it is used for oil sludge treatment system when the clients need 20~25m3/h treating capacity.


We will also show vertical G dryer GNCD930, it works together with GNLW363CG-VFD decanter centrifuge as drilling cuttings treatment system for oil based mud.
4 panel shale shaker GNZS594E installed with composite material shaker screens, with longer service life and better performance. We produce shaker screens in our own workshop, so GN solids control can control the quality by our own quality control dept. without purchasing from other suppliers. We produce OEM shaker screens for own shaker and replacement shaker screens for US brand shale shaker, like Derrick, Swaco, Brandt, FSI, Kemtron, etc.


Continue reading “Meet Good manufacturer of decanter centrifuge at CIPPE 2018”

Meet Good manufacturer of decanter centrifuge at CIPPE 2018

If you are looking for a good manufacturer of decanter centrifuge, vertical cuttings dryer, shale shaker, shaker screens, welcome to visit GN solids control stand at CIPPE 2018 to check our equipments.
Our stand info is as below:


We will show our best sold model decanter centrifuge at the show. As the largest and most professional oilfield industry products and service exhibition in China, all of the manufacturers will show their most advanced technology during the show.
GNLW363CG-VFD decanter centrifuge is one of the best sold model for our international clients, it can be used for solids control system, drilling waste management system, industry waste water treatment, dredging slurry separation, dewatering system, barite recovery, Low gravity solids separation, etc.


GNLW553C-VFD decanter centrifuge is the best sold big bowl big volume centrifuge, it is normally used as dewatering centrifuge with chemical dosing system for waste water treatment, it can be used for all kinds of waste water treatment. Sometimes it is used for oil sludge treatment system when the clients need 20~25m3/h treating capacity.


We will also show vertical G dryer GNCD930, it works together with GNLW363CG-VFD decanter centrifuge as drilling cuttings treatment system for oil based mud.
4 panel shale shaker GNZS594E installed with composite material shaker screens, with longer service life and better performance. We produce shaker screens in our own workshop, so GN solids control can control the quality by our own quality control dept. without purchasing from other suppliers. We produce OEM shaker screens for own shaker and replacement shaker screens for US brand shale shaker, like Derrick, Swaco, Brandt, FSI, Kemtron, etc.


Continue reading “Meet Good manufacturer of decanter centrifuge at CIPPE 2018”

Centrifuges and Its Multi-functional Applications

As the leading manufacturer of solids control and drilling waste management systems and equipments, GN Solids Control has a complete series of decanter centrifuges which are suitable for oil and gas industry. Those centrifuges cover a wide range of optional bowl diameters including 9 inch diameter bowl, 14 inch diameter bowl, 18 inch diameter bowl and 22 inch diameter bowl.

GN Centrifuges are widely used for industries of following:

  1. oil and gas solids control,
  2. barite recovery,
  3. drilling cuttings waste management
  4. drilling fluid waste management

waste-oil-recovery

Among GNLW series decanter centrifuges, you can find the suitable model for both the weighted mud and unweighted mud, and GN has high speed decanter centrifuge and middle speed decanter centrifuge respectively for 2-5 microns and 5-7 microns solids particles separation work. And GNLW series decanter centrifuges could use VFD control panel, in this case, for the same decanter centrifuge, end user could use it at any bowl rotating speed from 0 RPM to the maximum RPM of the centrifuge designed RPM. Like GNLW363CG-VFD, the max speed is 3900RPM and it could be used as both solids control decanter centrifuge and drilling waste management decanter centrifuge.

Besides using the decanter centrifuge for the physical separation, GN Solids Control’s new products, which employed in the chemical and thermal solutions also use Decanter Centrifuges as below:

  1. Dewatering unit and dewatering centrifuge. Dewatering unit is to use some chemicals to flocculate the extra fine particles into larger ones, and the next move is to separate it out with decanter centrifuge or filter press. GN Decanter centrifuge is used for dewatering centrifuge and the efficiency could reach 95%.
  2. Thermal Desorption Unit, it is used to separate the liquid phase from the solids, and then use thermal way to burn the oil from the solid and separate the oil and water by an oil water separator, in this case, decanter centrifuge is the first step for separation.

If you have specific request, or need more information for reference, welcome to contact GN directly.